Good morning,

I am trying to configure a 7609 router with SUP7203BXL, SIP-400 and SPA5xGE as BRAS. Here is my configuration:

version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
service counters max age 10
!
hostname R7609
!
boot-start-marker
boot system disk0:c7600s72033-advipservicesk9-mz.122-33.SRE1.bin
boot-end-marker
!
!
aaa new-model
!
!
aaa authentication login default local
aaa authentication enable default none
aaa authentication ppp default group radius
aaa accounting network default
 action-type start-stop
 group radius
!
aaa session-id common
!
ip source-route
!
ip domain name 7609PPP.com
ip name-server Y.Y.Y.40
ip name-server Y.Y.Y.20
!         
vtp mode transparent
mls flow ip interface-full
no mls flow ipv6
no mls acl tcam share-global
mls cef error action freeze
multilink bundle-name authenticated
!
spanning-tree mode rapid-pvst
no spanning-tree optimize bpdu transmission
spanning-tree extend system-id
!
diagnostic bootup level complete
diagnostic cns publish cisco.cns.device.diag_results
diagnostic cns subscribe cisco.cns.device.diag_commands
!
redundancy
 main-cpu
  auto-sync running-config
 mode sso
!
vlan internal allocation policy ascending
vlan access-log ratelimit 2000
!
bba-group pppoe Servidor_PPPoE
 virtual-template 1
 sessions per-mac limit 1
 sessions per-vlan limit 6000
!         
interface Loopback1
 ip address X.X.X.X 255.255.255.0 secondary
 ip address 10.10.0.1 255.255.0.0
 no ip redirects
!
interface GigabitEthernet5/1
 no ip address
 shutdown
!
interface GigabitEthernet5/2
 no ip address
 shutdown
!
interface GigabitEthernet8/0/0
 no ip address
 shutdown
 negotiation auto
!
interface GigabitEthernet8/0/1
 description PPPOE_IN
 no ip address
 negotiation auto
 pppoe enable group Servidor_PPPoE
!
interface GigabitEthernet8/0/1.100
 description VLAN_PPPOE
 encapsulation dot1Q 100
 pppoe enable group Servidor_PPPoE
!
interface GigabitEthernet8/0/2
 no ip address
 negotiation auto
!
interface GigabitEthernet8/0/2.10
 description PPPOE_Out
 encapsulation dot1Q 10
 ip address Y.Y.Y.1 255.255.255.0
!
interface GigabitEthernet8/0/3
 no ip address
 negotiation auto
!
interface GigabitEthernet8/0/3.55
 description To_Radius
 encapsulation dot1Q 55
 ip address 172.20.3.7 255.255.255.192
!
interface GigabitEthernet8/0/4
 no ip address
 shutdown 
 negotiation auto
!
interface Virtual-Template1
 description Template_PPPoE
 ip unnumbered Loopback1
 ip policy route-map toallot
 peer default ip address pool PPPoE_pool
 ppp authentication pap
!
interface Vlan1
 no ip address
!
ip local pool PPPoE_pool 10.10.0.10 10.10.255.254
!
no ip http server
no ip http secure-server
ip route 0.0.0.0 0.0.0.0 Z.Z.Z.1
ip route 192.168.50.0 255.255.255.248 172.20.3.1
radius-server attribute nas-port format d
radius-server attribute 31 mac format unformatted
radius-server attribute 31 send nas-port-detail mac-only
radius-server host 172.20.3.12 auth-port 1812 acct-port 1813 key --------

The session are created but clients can't reach internet.(The 7609 itself can reach internet)

I have a 7206VXR working with the same configuration.

I can see a difference between them. Virtual-Interfaces in the 7200 appears with the public ip address that Radius gives them but the virtual-Interfaces in the 7609 has the local pool i configured for the template.

I imagine that the 7609 works in a different way so that the configuration running on the 7200 had to be changed.

Any suggestion or idea?

Thanks in advanced!!