What command can I issue to see the current power (POE and System Power) on a Cisco 3650 Switch running IOS 3.07.04E.
Sh Env Power
#shows me power supplies, not usage.
Sh Power Inline
#show me the inline power consumption and usage.
Thanks
Network Engineering Stack Exchange is a question and answer site for network engineers. It only takes a minute to sign up.
Sign up to join this communityPower consumption on Cisco's new 3650 platform is very variable. It all depends on traffic flow, PoE and utilization of ports on the switch model. Cisco has made a Power Consumption table, which shows different usage for different scenarios. It's available via the provided link. Picture is for future reference. Remember to add your inline power of Access points, IP phones or cameras.
It is not possible to show the live power consumption via IOS.
Source: Look for table 12
energywise domain Cisco security shared-secret test1234
Interface config: int range gi1/0/1-24
<enter> energywise
<enter> - I then tried to check usage: sh energywise usage children
gave som totals, but it looks like the max for the switch is always 250W used. But the Access points give correct usage: Gi1/0/1 APXXXX.XXXX.XXXX 6.7 (W)
I can't find any 3650's at the moment but I have a 3850 running 3.7.3E. Looks like it will tell you the actual consumption.
Switch#show power inline police
Module Available Used Remaining
(Watts) (Watts) (Watts)
------ --------- -------- ---------
1 1800.0 215.6 1584.4
Interface Admin Oper Admin Oper Cutoff Oper
State State Police Police Power Power
--------- ------ ---------- ---------- ---------- ------ -----
Gi1/0/1 auto off none n/a n/a n/a
Gi1/0/2 auto off none n/a n/a n/a
Gi1/0/3 auto off none n/a n/a n/a
Gi1/0/4 auto off none n/a n/a n/a
Gi1/0/5 auto off none n/a n/a n/a
Gi1/0/6 auto off none n/a n/a n/a
Gi1/0/7 auto off none n/a n/a n/a
Gi1/0/8 auto off none n/a n/a n/a
Gi1/0/9 auto on none n/a n/a 2.7
Gi1/0/10 auto on none n/a n/a 2.5
Gi1/0/11 auto on none n/a n/a 2.6
Gi1/0/12 auto on none n/a n/a 2.7
Gi1/0/13 auto on none n/a n/a 2.6
Gi1/0/14 auto on none n/a n/a 2.7
Gi1/0/15 auto off none n/a n/a n/a
Gi1/0/16 auto on none n/a n/a 2.7
Gi1/0/17 auto on none n/a n/a 2.7
Gi1/0/18 auto on none n/a n/a 2.7
Gi1/0/19 auto on none n/a n/a 2.6
Gi1/0/20 auto on none n/a n/a 2.7
Gi1/0/21 auto on none n/a n/a 2.7
Gi1/0/22 auto on none n/a n/a 2.6
Gi1/0/23 auto on none n/a n/a 2.7
Gi1/0/24 auto off none n/a n/a n/a
Gi1/0/25 auto off none n/a n/a n/a
Switch#show power inline gigabitEthernet 1/0/20 detail
Interface: Gi1/0/20
Inline Power Mode: auto
Operational status: on
Device Detected: yes
Device Type: Ieee PD
IEEE Class: 3
Discovery mechanism used/configured: Ieee and Cisco
Police: off
Power Allocated
Admin Value: 60.0
Power drawn from the source: 15.4
Power available to the device: 15.4
Actual consumption
Measured at the port: 2.7
Maximum Power drawn by the device since powered on: 3.6
Absent Counter: 0
Over Current Counter: 0
Short Current Counter: 0
Invalid Signature Counter: 0
Power Denied Counter: 0
Power Negotiation Used: None
LLDP Power Negotiation --Sent to PD-- --Rcvd from PD--
Power Type: - -
Power Source: - -
Power Priority: - -
Requested Power(W): - -
Allocated Power(W): - -
Four-Pair PoE Supported: Yes
Spare Pair Power Enabled: No
Four-Pair PD Architecture: N/A
Switch#show ver
Cisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version 03.07.03.E RELEASE SOFTWARE (fc3)