1

While plug in a SM-X-ES3D-48-P Etherswitch Module into a Cisco ISR 4451 the Ports for this Module didn't came up. What I need to do to get the Ports enable with sh ip int br command?

The Output of sh hw-module all attribute is:

Slot 0 Bay 0 Board 0 Module[ISR4451-X-4x1GE] spa_type 0x76E Daughter Board Not Present
Basic attributes : length 11, version [2], module-type [ngio-virtual], width [unknown]
Power Rating [0], Control Endpoint count [0], Daughter Board Count [0]
KR Support [0x00], 16-bit GPIO [Not present], Submodule reset support [Not required]

Extended Attributes for [Front Panel 4 ports Gigabitethernet Module]
Port Count 4 Per-port Information : Type [Ethernet] Max IID [0] Connector [RJ45] Network clocking [disable]
Module OID: 1 3 6 1 4 1 9 12 3 1 9 92 21 
Port OID: 1 3 6 1 4 1 9 12 3 1 10 109 


Slot 1 Bay 0 Board 0 Module[SM-X-ES3D-48-P] spa_type 0xB4B Daughter Board Not Present
Base mac_addr 00da.55b0.e300 mac_blk_sz 128  Endpt MAC Address offset(s) : 52 
Basic attributes : length 11, version [2], module-type [alien], width [Double Wide-no aux]
Power Rating [100], Control Endpoint count [1], Daughter Board Count [0]
KR Support [0x00], 16-bit GPIO [Present], Submodule reset support [Required]

Extended Attributes for [SM-X-ES3D-48-P: EtherSwitch SM L3 + PoEPlus + MACSec + 48 10/100/1000 + 2 SFP]
GPIO Pin Information
Output Pin[Sub module reset]
Input Pin[PRI interface ready]
Output Pin[Reset config]

I2C Information
[dev_addr 0xB dev_type quack]

Port Count 2 Per-port Information : Type [Ether-Internal] Max IID [0] Connector [RJ45] Network clocking [disable]
Module OID: 1 3 6 1 4 1 9 12 3 1 9 96 6 
Port OID: 1 3 6 1 4 1 9 12 3 1 10 109 

In the docu for this module I can't find a way to activate this 48 Ports and sh ip int br Command didn't show the Ports. What can I do?

8
  • What do you mean? Are you trying to use these switch interfaces as router interfaces? That won't work.
    – Ron Maupin
    Aug 29, 2017 at 6:29
  • No I want to use this interfaces as switched interfaces but I can't see this interfaces in sh ip in br
    – kockiren
    Aug 29, 2017 at 6:30
  • Do you see the interfaces when you show the configuration?
    – Ron Maupin
    Aug 29, 2017 at 6:31
  • No in sh run also no interfaces only the internal 4 Gi Interfaces
    – kockiren
    Aug 29, 2017 at 7:08
  • What can I do to add this extra Interfaces? The new interfaces are on same level as the old ones? I aspected the new Interfaces in Gi1/0/x
    – kockiren
    Aug 29, 2017 at 11:18

1 Answer 1

1

The EtherSwitch Module isn't a routing module, so you can't see the EtherSwitch Port if you connected to the ISR Router. You need to connect to the EtherSwitch module separate with following Command:

hw-module session 1/0

The Part 1/0 of above command depend from the Output of sh hw-module all attribute Command:

...
Slot 1 Bay 0 Board 0 Module[SM-X-ES3D-48-P]
...

1/0 is for Slot 1 Bay 0, than you connect to the EtherSwitch command and can configure this one.

This site is temporarily in read-only mode and not accepting new answers.

Not the answer you're looking for? Browse other questions tagged .