4

In my Multiarea-OSPF configuration I can ping my neighbor, but nobody which is more than one hop away (for instance ABR2). Also traceroute just shows "1 * * * - 2 * * * - 3 * * *"

Can anybody think of possible mistakes in the OSPF configuration?

enter image description here

configuration: 

en
 conf t
 no ip domain-lookup
 ipv6 unicast-routing

 int loopback 0
  ip address 2.2.2.2 255.255.255.0
  exit

 ipv6 router ospf 1
  area 45 range 2001:db8:18:4500::/56
  auto-cost reference-bandwidth 100000
  router-id 2.2.2.2
  exit
 router ospf 1
  area 45 range 10.45.0.0 255.255.0.0
  area 0 range 10.0.0.0 255.255.0.0
  auto-cost reference-bandwidth 100000
  network 10.45.0.0 255.255.255.252 area 45
  network 10.45.0.4 255.255.255.252 area 45
  network 10.0.0.0 255.255.255.252 area 0
  network 10.0.0.4 255.255.255.252 area 0

 int s0/1/0
  ip add 10.45.0.1 255.255.255.252
  ipv6 add 2001:db8:18:4501::1/64
  ipv6 ospf 1 area 45
  ip ospf hello-interval 3
  ipv6 ospf hello-interval 3
  no sh

 int s0/1/1
  ip add 10.45.0.5 255.255.255.252
  ipv6 add 2001:db8:18:4502::1/64
  ipv6 ospf 1 area 45
  ip ospf hello-interval 3
  ipv6 ospf hello-interval 3
  no sh

 int s0/0/0
  ip add 10.0.0.2 255.255.255.252
  ipv6 add 2001:db8:18:0001::2/64
  ipv6 ospf 1 area 0
  ip ospf hello-interval 3
  ipv6 ospf hello-interval 3
  no sh

 int s0/0/1
  ip add 10.0.0.6 255.255.255.252
  ipv6 add 2001:db8:18:0002::2/64
  ipv6 ospf 1 area 0
  ip ospf hello-interval 3
  ipv6 ospf hello-interval 3
  no sh
Improve this question
12
  • Why did you delete the configuration? – user36472 Feb 19 '18 at 9:54
  • because it's hard to see what someone's got wrong just by looking at one configuration and not knowing the network-topology/ip-scheme. Or should I put the config back again in the question? – watchme Feb 19 '18 at 9:57
  • Even better, put the configuration back and add a simpel topology drawing. :-) – user36472 Feb 19 '18 at 9:59
  • @Cown done :-) . – watchme Feb 19 '18 at 10:09
  • 4
    Network command in ospf uses wildcard bits. Use 0.0.0.3 instead of 255.255.255.252 etc. Or simply use ip ospf 1 area 0 though I'm not sure this is supported in PT's image. – ar_ Feb 19 '18 at 10:27
3

As @ar_ pointed out in the comments of my question: The problem was, that I configured the network command in a wrong way. So I used subnetmasks instead of wildcard masks. (network-commands in OSPF need wildcard masks).

@RonMaupin added the information in the comments of this answer, that in the newest IOS-version both ways (subnetmask and wildcardmasks) work.

Improve this answer
8
  • 1
    Although, the very latest IOS versions seem to correct that for you. – Ron Maupin♦ Feb 21 '18 at 16:48
  • @RonMaupin Do you mean it can handle both, subnet- and wildcardmask? – watchme Feb 21 '18 at 16:52
  • Yes, but you probably should use one or the other, otherwise it could be very confusing when looking at it. I suppose it looks to see where the consecutive bit are (at the beginning or end) to determine how to interpret it. – Ron Maupin♦ Feb 21 '18 at 16:55
  • I'm not sure at which version this was added. – Ron Maupin♦ Feb 21 '18 at 16:55
  • @RonMaupin How can it distuingish when the subnetmask is 0.0.0.0 for instance? – watchme Feb 21 '18 at 17:03

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.