Questions tagged [cisco-4500]
For questions about or involving the Cisco 4500 Series switch. For instance, you are setting up a new 4500E with Supervisor 8E.
17
questions
13
votes
2
answers
23k
views
How can I verify QoS DSCP marking on a Cisco Catalyst 4500E?
Good afternoon,
I've got a shiny new 4500E running 15.0(1r)SG7 that is set to replace an ailing 3750E.
It is running ipbase for now.
On the 3750 I was able to check out the incoming DSCP/CoS values ...
- 311
9
votes
1
answer
7k
views
Is there any limitation of Secondary IP address number on a SVI or interface on 450x?
After a search on configuration guide and documentation, I didn't any evidence of a limitation on ip address secondaryconfiguration on a certain VLAN on 450x SUP6E.
Anyone know where I can found ...
- 2,008
6
votes
2
answers
3k
views
Cisco NTP server does not respond to queries
I have an NTP configured through out our in a hierarchy. 100% reliable with regards to providing time for Cisco devices. At one of our sites we allow cameras, servers, and workstations to utilize our ...
- 799
5
votes
1
answer
1k
views
ACL on entry of Core Switch - Performance doubt
We are an ISP and I would like to implement ACL to protect our core network (Infrastructure) and implement some filtering on public subnet inside.
As border device we have a cisco WS-C4500X-32 4500x ...
- 2,008
5
votes
2
answers
2k
views
4500E / 4500X VSS pairing
Is it possible to combine a 4500E with a 4500X into a VSS pair or do they have to be the same model to pair up? If it requires same model, is it due to hardware or software? For example if it is ...
- 3,129
4
votes
1
answer
826
views
Will the Cisco 4500-X have OnePK/SDN Support?
At the Cisco 4500 Chassis model comparison page it says the Supervisor 7E is "Hardware Ready" for SDN. It was released in late 2011. URL for that page can be found here: http://www.cisco.com/en/US/...
4
votes
2
answers
574
views
Interface capabilities: CISCO 2960S vs WS-X4648
We are going to deploy customer access switches. We can chose between two switch solutions: 1) CISCO 2960S 2) line card WS-X4648 in CISCO 4507R+E (Sup7L-E). Our customers will work with video ...
- 831
4
votes
1
answer
3k
views
Conf-reg and ISSU
I am trying to do an ISSU on Cisco 4k switch.
1) I booted both of the supervisor of the switch with the same image.
2) I also used the boot system bootflash command with both of the image names, ...
- 193
3
votes
2
answers
651
views
Cisco Catalyst - Switching with Supervisor and Line Cards
Regarding the Cisco Catalyst 4500, or 6500, does the frames switching and the packets switching (with CEF) are performed by the Supervisor Card or by the Line Card ? (Also, does a Line Card has CAM ...
- 1,085
3
votes
1
answer
786
views
Cisco - supervisor reset without disabling interfaces
After power loss we have an issue with supervisor on 4500~ cisco switch.
Peer (slot: 3) information is not available because it is in 'DISABLED' state
But interfaces that are in that card are ...
- 31
3
votes
2
answers
293
views
Cisco catalyst 45xx series compatibility with RG45 10Gb
I'm looking for a compatible RG45 10Gb line card with Cisco catalyst WS-C4507R+E/WS-X45-SUP7-E
Unfortunately I was unable to find any useful information in data sheets.
Can anyone help me? I'm really ...
2
votes
3
answers
771
views
Does Catalyst 4500x-16s support 10/100 network devices?
Does 4500x-16s support 10/100 network devices? My vendor says that it is not able to and one of my devices can only support 10/100.
- 123
2
votes
2
answers
1k
views
Want to disable TenGbE to enable 1GbE Gbics in Cisco 4500
This is my first post into Cisco Forum, however I'm used to check it for every question or problem I have.
I'm putting back in production a Cisco 4507R-E switch with two supervisors, and what I need ...
- 95
1
vote
2
answers
625
views
VSS back to back like vPC back to back
I know vPC back to back to avoid spanning tree between two pairs of Nexus.
But I've two 4500 pairs and I need to connect them. Is there a way to do something similar to the vPC back to back to don't ...
- 180
1
vote
1
answer
633
views
Cisco 4510R crash "Last reset from Abort"
Had a crash showing on a EOL/EOS 4510R. Can the crash be determined from the first few sections of the crash dump file.
Also had a crash a month ago, and I consistently see the same BusErrAddr=...
- 7,094
0
votes
1
answer
691
views
C4510RE terminated abnormally
Hi I am unboxing 2x cartons of C4510RE chassis and find this booting up fault consistently appearing in both chassis.
Has anyone encountered this before?
Please find below logs:
Cisco IOS Software,...
- 13
0
votes
2
answers
396
views
Unable to ping but I can see the arp in switch 4451
Recently I got to know that I am unable to ping the IP addresses behind vlan236 from core1 whereas I am able to ping the same from core2 and able to ping the IP address of vlan236 from my laptop as ...
- 1