Questions tagged [cisco-catalyst]

A tag for questions related to Cisco's Catalyst line of switches.

Filter by
Sorted by
Tagged with
-2
votes
0answers
11 views

Networking configuration and submitting [duplicate]

The 131.181.112.0/22 network is provided. a) Determine the number of subnets that can be obtained with that IP address b) Determine the number of available hosts on that network. c) Design 6 subnets ...
0
votes
0answers
16 views

ASA ping outside to inside private ip's?

i am new asa and cisco as well , what i am trying to do to perform this lab , only 1 issue is there , i need help in it, i can ping from pc0 to router0 in other way I can ping inside to outside , but ...
0
votes
1answer
31 views

Cisco Port forward ip nat inside source static … Invalid

This is almost the same question as How to setup port forwarding on Cisco Router running Version 15.2(4)M6. The problem is that the command used in the answer is not available: ip nat inside source ...
0
votes
1answer
20 views

Cisco 9300 Stacking Issue — Link OK Yes, Link Active No

hopefully another pair of eyes can help me out with this. We have 4 Cisco 9300-24Ts data-stacked with all cables detected by the switches themselves. Switch order and priority looks good, however we ...
0
votes
1answer
43 views

How do I find out the thoroughput of a Cisco Switch?

I am trying to find out the thoroughput of our Cisco 2960 & SG300 switches. Is there a CLI code I can run to find this?
0
votes
1answer
86 views

Best practice / advice for cisco 3560 behind Virtualised OPNsense

Currently I run the below scheme. The problem is that when ESXi is down it takes down all the network with it, so I have to boot up another router to log in to it. WAN > OPNsense (in ESXi)> ...
0
votes
1answer
582 views

intervlan routing with PfSense

I Need some guidance on getting my lab networking configured. Any support is appreciated. My Lab consists of: 2 cisco switches: 2960s(access layer 2) and 3750X(ip routing/layer 3) Xenserver with ...
7
votes
1answer
843 views

How to break apart an IPv6 /56 6rd delegated prefix from ISP into multiple /64 VLANs for use with SLAAC EUI-64? [Cisco]

I have CenturyLink Internet service, and they have a 6RD IPv6 deployment where they hand out an IPv6 delegated prefix /56 block to me and allow me to use it as I wish. My Cisco ISR router receives the ...
1
vote
1answer
53 views

PortFast For Some Networks But Not Others

I have 4 offline self contained networks. They are setup as such: Network 1: Windows Server 2016 As Domain Controllers And Windows 10 (1909) Clients Connected by Cisco C9300-24Ps. Network 2: Windows ...
4
votes
3answers
27k views

Meaning of the ip default-gateway L2 switch

What is meaning of the ip default-gateway command on a Cisco L2 switch? I read something about it on the Internet, but there was written that it allows you to Telnet to the switch. I am little bit ...
1
vote
0answers
31 views

Cisco QinQ - More than one s-vlan on dot1q-tunnel for the same c-vlans

I have a scenario where I have 3 service vlans (10,20,30) from a trunk port and need to brige our customer vlans (100,200,300,400) between all the service vlans. I need to do it all in the same switch ...
0
votes
1answer
40 views

When do ACLs on SVIs get applied on Cisco Catalyst devices?

I don't understand exactly when an ACL will get applied when on an SVI. Given the following (pseudo) configuration int vlan 100 ip address 10.0.0.1 255.255.255.0 ip access-list in in ip access-...
3
votes
1answer
89 views

cisco switchport trunk native vlan

we have switch catalyst 3850 and we need to enable the PXE boot on a port configured in trunk with configured three VLAN (4040, 4050 and 4060). To permit the PXE boot and deploy to work we set on the ...
1
vote
1answer
55 views

QoS policy definition - Cisco guidelines vs reality

Currently designing a QoS Policy for a customer (Cat 4500 models), following the business needs, I will work on a 8-class based model definition. Cisco has several guidelines under this perspective, ...
2
votes
1answer
449 views

Link Aggregation from Cisco to Palo Alto using 10 gig interfaces, port on Cisco shows “waiting to be aggregated”

I am trying to bundle two 10-Gig interfaces on PA-3020 to Cisco Cat9300. Previously, I had bundled two Gigabit interfaces on same devices and everything worked fine. But now, when I try to configure ...
2
votes
1answer
98 views

Cisco C3750X power supply: difference between /1 vs /2?

What is the difference between the C3KX-PWR-350WAC/1 and C3KX-PWR-350WAC/2 power supplies for the Catalyst 3750X series? I have a bad power supply, and I can't remove the failed one right now to ...
0
votes
0answers
72 views

Cannot create connection between two routers in same VLAN via switch

I currently have a Cisco 2960-24TT switch (switch1) and a Cisco 1841 router (router1) that form part of my core network connecting other VLANs and devices. The two ports on router1 have been ...
0
votes
0answers
47 views

Cisco C3750 and PRTG netfllow

I have a core switch (backbone) of our network that broadcasts all the vlans to other switches. I am trying to configure netflow on the switch and link it up to a Netflow sensor on PRTG. I followed ...
0
votes
1answer
175 views

Unable to ping between router and routed port on L3 switch. Why?

I've got an old Cisco 2811 connected to an old Cisco 4948 L3 Switch. I'm trying to teach myself a little more about L3 Switch implementation. All I'm trying to do at this point is get the router and ...
2
votes
1answer
581 views

Why would you use port security mode “protect?”

Port security offers three violation mode options: • protect—Drops packets with unknown source addresses until you remove a sufficient number of secure MAC addresses to drop below the maximum value....
1
vote
1answer
258 views

Is it possible to use a interface of Catalyst on a ISR

We use Cisco Catalyst 3850 Switch (with Cisco One Foundation) as aggregation Switch for multiple Lines and connect it to a ISR 4451 for routing. Now we search for a solution to use the Interfaces of ...
1
vote
1answer
136 views

Segregated OSPF Networks, cross same physical path, how to segregate back out at other end?

I'm sorry for being basic in writing this question. I think the details have been covered though. What's happening here is, two separate networks are being brought into an isolated area over a ...
2
votes
1answer
2k views

Configure Routing on Catalyst 3650 with LAN Base

I am attempting to configure routing on a Catalyst 3650 running LAN Base to meet a particular set of criteria. For context: the switch is being configured as part of a lab environment that will allow ...
2
votes
1answer
3k views

Auto Voice VLAN on Catalyst 2960X running IOS 15.2(2)

I am looking to reproduce a configuration that I have quite easily achieved on the Cisco Small Business Series SG500 family of switches. The configuration is for Auto Voice VLAN, triggered by CDP and/...
4
votes
2answers
860 views

Trust dscp command missing on cisco 3850

We have an incoming QoS configuration on our 2960X switches like this: class-map match-any QOS_GL_TRUST match ip dscp 8 16 24 32 46 class-map match-any QOS_GL_CITRIX match access-group name ...
8
votes
1answer
1k views

Native Vlan Cisco Catalyst and Layer 3 switch

I have run into an interesting issue setting the native VLAN between one of my Cisco Catalyst 2960 and my Layer 3 switch (third party). Here is the setup, the layer three switch is set up to run on ...
4
votes
1answer
2k views

Cisco Catalyst 2960 X MAC access list

I am using a MAC access list on this switch, so I go about it by first creating the MAC access list: #conf t #mac access-list extended aclname # permit host XXXX.XXXX.XXXX any Then, I tie this list ...
4
votes
1answer
3k views

Adding a new switch to a C9300 stack

We currently have a stack of Catalyst 9300, like this : SW1 (master) SW2 SW3 We plan on adding a 4th switch, SW4, but in between SW2 and SW3. This would give: SW1 SW2 SW4 SW3 My question is : ...
6
votes
2answers
4k views

VLAN Interface is down, protocol is down

I have Cisco Layer 3 switch with IP routing enabled on it. I have different VLANs configured on it and its working perfectly. Now i have added another VLAN (SVI) and assigned that VLAN to one of the ...
5
votes
2answers
3k views

Why does a switch have more VTY lines than a router?

During my years working with Cisco equipment I realised that switches have more VTY lines (16) as compared to routers which have 5 VTY lines considering that the equipment that we work with (c2960 ...
3
votes
2answers
13k views

Remove interface VLAN 1 in cisco 2960 switch

From what I understand, there are protocols like VTP and CDP that no matter what will use VLAN 1. CDP and VTP are layer 2 meanwhile interface VLAN is layer 3. So, I wonder why I cannot delete ...
1
vote
3answers
209 views

Cisco Switching Lab

Could you please advise with some ideas on how to setup a Switching lab in a production enviroment without harming the Production ? Basically I need 3 Cisco Switches where I can try some labs but ...
3
votes
3answers
3k views

Operational mode is down for one link

I am setting up a simulated Cisco Packet Tracer with three Cisco Catalyst 2960 switches S1, S2 and S3. S1 being the trunk for S2 and S3. I have three(3) interfaces F0/6, F0/11, F0/18 that are ...
2
votes
2answers
433 views

DHCP on CISCO 3850

I would like to configure the DHCP server on CISCO 3850, and reserve around 100 static IP for servers After doing research found that I need to create individual pool for each static maping like ...
3
votes
1answer
1k views

NetFlow configuration on Catalyst 4500-X

I have a problem with config NetFlow on 4500-X switch. This is NetFlow config flow record NFArecord match ipv4 tos match ipv4 protocol match ipv4 source address match ipv4 destination address ...
1
vote
1answer
142 views

TCP handshake immediately RST [closed]

I'm trying to set up a modbus TCP connection on port 502 but get a RST packet immediatly. So the TCP connection handshake doesn't even succeed. This is done on a windows machine on an ESX server. The ...
0
votes
2answers
129 views

What does the Cisco HTTP client (help to) do on a switch?

While checking for vulnerabilities in one of our Cisco switches I came upon this: CVE-2019-12665. Excerpt from the CVE: A vulnerability in the HTTP client feature of Cisco IOS and IOS XE Software ...
0
votes
2answers
1k views

Why does yealink ip phone is not getting ip address from voice vlan?

I have configured separate vlan for voip and connected interface to it (as shown below). But the phone is not getting ip address automatically. switch- cisco 2960-x phone- yealink I had tried: (on ...
5
votes
3answers
8k views

How to trunk VLANs over Layer 3 EtherChannel?

I am trying to setup a network that includes an EtherChannel link between two Cisco Layer 3 switches (Catalyst 3750). I am using a collapsed core hierarchical network. The picture above is my ...
0
votes
1answer
81 views

N2K-C2248TP-1GE question

We are working with Cisco 2960 and Cisco 4948 switches as our top of rack switches and we want to purchase some N2K-C2248TP-1GE , and connect N2K-C2248TP-1GE to our edge switches, (our edge switches ...
0
votes
1answer
93 views

Vlan Command Issues on Cisco Switches

I'm new to cisco equipment. I have GNS3 emulating an L3 switch whose image is "i86bi-linux-l3-adventerprisek9-15.5.2T.bin". I want to create a cable network with 802.1x and vlan authentication. For ...
1
vote
1answer
445 views

Switch cannot ping server [closed]

My switch won't ping my server. Both are directly connected with each other, and are in vlan 666. When I initiate a ping from my switch to my server, the switch sends ARP requests. Then the server ...
1
vote
1answer
175 views

`no ip bootp server` appear in `sh run`

My understanding on Cisco devices is if we put no command in the config mode, that particular line will be gone from sh run. But I notice there is specific line in sh run with no ip bootp server ...
1
vote
1answer
57 views

VLAN Across Trunked CISCO 2960-S Switches

With reference to the above diagram: Is 10.124.124.141 supposed to be able to ping 10.124.124.161 if the setup is correct ? There is no router in-between, the idea is that the VLAN 215 spans two ...
2
votes
2answers
937 views

Cisco 3750G - SSH Diffie Hellman Group 1 SHA1 Error

I recently implemented SSH configuration on my 3750G switch stack. I have -set the domain name -generated the rsa key using 2048 bits -ensured that the vty lines are set to transport input ssh Now ...
0
votes
2answers
110 views

Multiple 802.1x clients, single port support on a Cisco 3750 switch?

I'm thinking of using our Cisco 3750 switch with our RADIUS server for 802.1x authentication on our Ethernet ports. If I enable 802.1x and a user connects a switch to their Ethernet jack, and the ...
1
vote
1answer
184 views

Migrating Configuration - 3750G to 3750X

What is the best practices to migrate configuration from an older Cisco switch model to a newer Cisco switch model? -I am not expecting to change any configuration, just simply want to be on the ...
3
votes
1answer
121 views

Switching interface VLAN ID Mid-Production

I was wondering if there was a way to switch out the VLAN ID from VLAN1 to VLAN10 without impacting the connectivity of the end users? Can I simply copy and paste from one interface VLAN to another? ...
0
votes
0answers
60 views

Cisco Catalyst QoS queuing model

How Cisco Hardware queuing model (like 1p7q4t for Cat6800) are related to traffic classes (class-map) ? How assign the X traffic class to Y hardware queue ? Also, if only 6 classes are configured, ...
5
votes
2answers
633 views

Should portfast be configured on the physical interfaces or on the logical port-channel, or both?

I'm using a Cisco 3750 switch and have two physical ports configured in a port channel that connects to a router. Should I configure spanning-tree portfast on the physical interfaces or on the port-...

1
2 3 4 5
7