We’re rewarding the question askers & reputations are being recalculated! Read more.

Questions tagged [dell]

For questions about or in relation to all network devices produced by Dell Networking.

Filter by
Sorted by
Tagged with
1
vote
1answer
109 views

Dell PowerConnect 6248 experience

Does somebody have experience with the Dell PowerConnect 6248 for the datacenter usage with high traffic? Does it run stable and can it passthrough 10gbit? How is your performance experience?
2
votes
1answer
2k views

Setting up a new Meraki MS220-48FP Switch to replace a pre-existing DellForce10 Switch

I have a new Cisco Meraki Switch that is replacing a DellForce10 switch that is already in place. I need to configure the Meraki switch to how the Dell switch is setup. The only thing that is ...
1
vote
1answer
2k views

Dell PowerConnect 2848 MCLI Mode

I have the switch put in production already Dell Power Connect 2848. Now im trying to put some ip address and configurations. The problem is that when i connect it through the serial i have just the ...
4
votes
2answers
2k views

How do I set up a Link Aggregation for 2 ports between a Sonicwall TZ500 and a Dell XP1018P

A LAG group on the X1018P managed switch is real easy but switch port configuration is not available on the TZ 500. Is there a way to set it up for 2 ports like x0 and x2 on the firewall and e15 and ...
1
vote
0answers
1k views

Block MSTP on port Dell N series networking

I am noticing that our Dell N4000 series switch connected to a stack of Cisco devices is constantly attempting to change spanning tree topology. The Cisco switch is our Internet connection and a fiber ...
2
votes
0answers
262 views

Windows 7 PC getting unidentified network and no network access on 1 wifi [closed]

Good afternoon guys. I have a Dell precision 4800 Laptop which is most of the time hooked up to the LAN at the users desk. Out on our production floor we have 4 Access Points, each on their own VLAN ...
0
votes
1answer
1k views

Passing Vlans between HP Procurve and Dell Powerconnect switches

I have a core switch which is a HP Procurve switch with Vlans 1, 10, 20. I'm trying to setup an edge Dell switch. On the HP I have untagged vlan 1 and tagged vlans 10, 20 on port 1. On the Dell ...
2
votes
1answer
1k views

Dell SonicWALL - TZ series Dual Wan

Can you use dual-WAN with Active/Passive failover on any of the TZ SonicWALL models?
3
votes
1answer
233 views

Unique MAC address in L3 switch

Dell 6224 is L3 switch: Does L3 switch have unique MAC address for different port?
2
votes
1answer
502 views

Dell 6248P Powerconnect Switch - Routing IP Configuration - What is it for?

This is a rather simple question but I cannot seem to find a resource that explains what this feature is for (without it simply saying "this is to configure an IP interface"....very helpful) Can ...
1
vote
0answers
816 views

Dell Switch N3048 with PowerConnect 6248

I have two Dell switches and its a classical VLAN Scenario that does not want to work. PowerConnect 6248 is connected to the outside world and from there i like to bring new subnet ( this is already ...
1
vote
0answers
608 views

PowerConnect 2808 and syslog

I have a pair of Dell PowerConnect 2808 managed switches. I am attempting to enable syslog on them, but not having any luck. I have searched the web interface, used telnet to log into the CLI ...
1
vote
1answer
256 views

Dell PowerConnect 6224P VoIP

We have an issue where the IP phones are getting DHCP IP's from the Data VLAN. Data - VLAN 10 VoIP - VLAN 15 As of right now, we are just working on one port before deploying a solution to the ...
0
votes
1answer
2k views

Default Configuration in Dell 5548 [closed]

I am new to Dell switches and have recently joined a company. There are two IP addresses configured on a 5548 PowerConnect. ip address 192.168.0.5 255.255.252.0 ip address 192.168.137.17 255.255.255....
4
votes
1answer
11k views

Dell N2000 - Inter-VLAN routing problem

I've been brought in to troubleshoot an issue on an install performed by a different engineer. The basic topology is: 1x Dell N2000 as Core Switch 1x Dell N2000 as Access Switch 01 1x Dell N2000 as ...
2
votes
2answers
1k views

Dell R720 and Cisco 2960S SFP+ connection

Can I connect a Dell R720 with a Broadcom 57840S Quad Port 10Gb SFP+ Direct Attach Rack Network Daughter Card (540-BBCN) and Cisco 2960S SPF connection? I'm using a Cisco Twinax cable and the ports ...
0
votes
1answer
154 views

Multi inbound networks on one switch - is it possible to mitigate high latency? [closed]

I am rather new to VLAN setups, and I am not sure if I understand the basic implementation. To save some bits, I'll attempt a quick and dirty run down of my setup. Here is a crude picture(drawing) to ...
3
votes
2answers
432 views

Trunking MGMT Vlan Cisco x Dell

@edit: SOLVED!!! - See my answer below! how's going? Scenario: Trunk two Switches (Dell 6224 and Cisco SF300) for accessing them from the MGMT VLAN. Cisco ge2 -------TRUNK-------> Dell 1/g22 ...
3
votes
1answer
2k views

Switch Redundancy with Dell N2000 series switches

I've just set up a rack with a SFP input into a Dell N2024, with a /28 routed to the switch which I can then use as required for devices within the rest of the rack. This is working fine from a ...
2
votes
2answers
5k views

VLAN with Mixture of Managed/Unmanaged Switches

I've got a setup in my house as a test to try and figure this stuff out, but i've hit a bit of an end point. Here is a picture of my network setup. So i have my internet provided by Virgin Media, ...
4
votes
2answers
10k views

TCP Retransmission and duplicate ACKs

I am having a problem with my core network. Currently I have a DELL PowerConnect 5524 which has a SFP+ (10Gbe) Module connected to another 5524 (Same transceiver on both) which is also stacked with a ...
10
votes
3answers
6k views

Setting up PIM Sparse mode

I am working on trying to setup our network for multicast traffic. In the coming months we will be installing new equipment that sends out multicast traffic. In the past we have only had 1 VLAN so we ...
1
vote
3answers
697 views

What is Dell's “Permanent” VLAN?

I am aware of the following types of Vlan's. Default VLAN: This is basically where ALL ports belongs to by default, this is technically VLAN 1 and it can't be deleted from the switch. Data VLAN: ...
7
votes
2answers
7k views

Dell PowerConnect 5524 VLAN routing

I have a Dell PowerConnect 5524 that I'm trying to configure. What I want is simple routing between VLANs and the user guide is less than helpful. On page 220, it says (or implies) that all you need ...
4
votes
2answers
2k views

Stacking Different Model Dell Switches

I have 2 brand new Dell 5448 1 Gbps switches and an older 3448P. The newer switches stack with each other via an HDMI cable and have the ports for fiber optic, but the older 3448P switch has no HDMI ...
9
votes
1answer
2k views

Dell powerconnect 6248 voice vlan next to dot1x

We are testing currently dot1x auth against FreeRADIUS/AD in the network. The vlans are dynamically assigned by FreeRADIUS on AD-group base. This works, but now the problem comes: We wanted to add ...
10
votes
3answers
4k views

Multiple LAN interfaces on SonicWALL

We have a SonicWALL 2400. Is there any way to assign multiple interfaces to the same LAN subnet? Basically, we would like to have X1 for the WAN and X0, X2, X3 and X4 connected to 4 devices that ...
6
votes
2answers
3k views

Changing the Stacking Configuration on four Dell M6220 blade switches

My main production environment is in a Dell M1000e blade chassis with M6220 switches in Fabrics B and C. Fabric B is dedicated to vMotion traffic, and Fabric C is dedicated to iSCSi traffic and ...