Episode #125 of the Stack Overflow podcast is here. We talk Tilde Club and mechanical keyboards. Listen now

Questions tagged [huawei]

A tag for questions involving Huawei networking hardware or software.

Filter by
Sorted by
Tagged with
4
votes
3answers
494 views

Multicast routing on Huawei Quidway 5300 Switches

I have been testing a scenario which involves multicast routing for multicast traffic the scenario is pretty simple. I have two L3 switches with OSPF running in between them, two computers are ...
4
votes
2answers
670 views

LACP Huawei S6720

Once here I ask about LACP between rb750 and huawei ne20, as @Zac67 said "throughput for multiple flows, not for a single flow" . I was testing from a single flow, now is working, but I came ...
4
votes
1answer
173 views

LACP: Between RB750 and Huawei Ne20

I'm making a test to create a PORT AGGREGATION between my RB750 and Huawei NE20. Rb750: Flags: X - disabled, R - running 0 R name="bonding1" mtu=1500 mac-address=D4:CA:6D:1D:6F:66 arp=enabled ...
3
votes
2answers
381 views

Equivalent Cisco EEM in Huawei

is there a Huawei feature works similar than Cisco EEM?? I want to shutdown an interface when a track goes down
3
votes
1answer
76 views

How can I filter the exact interface in huawei switch?

How can I filter the exact interface in huawei switch? you see when I use the include GigabitEthernet0/0/1 to filter, there will get many GigabitEthernet0/0/1* interfaces: <Z178A>dis ...
2
votes
2answers
79 views

Dose Huawei S6720 have GE port?

everyone! I want to buy a Huawei switch with GE ports, does Huawei S6720 model have GE port?
1
vote
3answers
1k views

Incorrect MAC address in switch MAC table [closed]

I'm trying to do up a wiring diagram for a VMWare cluster in a remote data center. I typically will check the MAC addresses in VMWare VSphere client (vmnic[x]) and/or use esxcli to do so from SSH on ...
1
vote
1answer
950 views

Ansible modules for automate switch Huawei S5700 configuration

Consulting Ansible webpage, I found modules for Huawei CloudEngine series (ce_command, ce_config, etc). But theses modules don't work for others families like switches S5700. So, what Ansible modules ...
1
vote
1answer
60 views

What's the AC meaning there?

What's the AC meaning there, see the bellow snapshot.
1
vote
1answer
243 views

RADIUS: Accounting is not establishing the session

I'm using Huawei Ne20 and a FreeRadius, the last has already been used to authentication Mikrotik accounts. I'm getting authentication accept message, but the accounting session is not being ...
1
vote
1answer
42 views

List brief information of HuaWei IOS

When I use display interfaces there shows many data. I have to use Space to skip pages to see more content. Description:HUAWEI, AR Series, GigabitEthernet0/0/1 Interface Route Port,The Maximum ...
1
vote
0answers
54 views

traffic of AF41 marking under interface

I have used port-queue commands most of the time to check traffic status under BE, EF, AF4. But I haven't found command to check for AF41 to AF42 on Huawei VRP or cisco IOS. How can check traffic of ...
1
vote
0answers
1k views

Huawei: Configuring netstream

I'm trying to configure NETSTREAM, but I'm a little confused. Following this tutorials: Configuring NetStream export and Huawei: NetStream Configuration. I'm configuring netstream on Huawei Ne20e ...
1
vote
0answers
376 views

Traffic Statistics per VLAN

I'm using Huawei s6720 and I would like to monitor traffic per vlan, example: # Interface GigabitEthernet0/0/6 port link-type trunk port trunk allow-pass vlan 200 300 400 500 # I can verify ...
1
vote
1answer
457 views

Huawei AR160 IPSEC over DSL Packet Loss

we are Struggeling with some IPSEC Configuration via a DSL Line on a Huawei AR169 Router. When the Tunnel is running over an PPPoE Dialer we notice about 70% Packet Loss in the Tunnel. When the ...
1
vote
0answers
66 views

Policy routing with IS-IS

three routers are connected where Router A connected to router B A (gig0/0/0 ip address 10.10.1.1)====> B(gig0/0/0 ip address 10.10.1.2 A(gig0/0/0=> ip address 10.11.1.1===>B(gig0/0/...
0
votes
3answers
975 views

Disabling paging in Huawei

I'm interacting with a MA5616 Huawei, and paging is enabled by default. So for a command like display adsl port state all, I'll be asked if I'd like to see more results. Is there anyway to disable ...
0
votes
1answer
150 views

How to see full description, When issuing “display ip interface description” ?? on huawei router

I have a router with many interfaces when I issue the command display ip interface description I get something similar to this Eth-Trunk1.444 10.2.2.2/28 U U <= Gige E To ...
0
votes
1answer
590 views

how to discover devices in a large heterogenous network with huawei, cisco, alcatel and more different devices without using snmp?

i have a huge task to do and i need your help.I am new to the whole networking world and I apologize if this is a re-post of a question. so what i wanted is to discover and mapping all my enterprise ...
0
votes
0answers
18 views

The huawei S2300's interface protocol become `--`

The huawei S2300's interface protocol become --: <HW>dis interface brief *down: administratively down ...
0
votes
0answers
32 views

Applying DSCP to an interface

I'm trying to apply DSCP (AF41) to an interface eth-trunk (if it matters) - [~HUAWEI] diffserv domain QoS \ creating diffserv domain named QoS [~HUAWEI] dsdomain QoS] ip-dscp-outbound af4 ...
0
votes
0answers
28 views

How to analysis the below situation, is the too many switch trunk connect caused this issue?

I have two Juniper EX switches, and the Juniper-EX-01(ge-0/1/1) connected to the Juniper-EX-02(ge-0/1/0). I want to check is there any optical attenuation problem, or other link errors. admin@...
0
votes
1answer
21 views

ma5603 - how to get ont port configuration via display command

how can i get the configured native vlan beside the ont-srvprofile from a display output which is not display current config ? I do have the ont-srvprofile configured as transparent but the native ...
0
votes
0answers
48 views

Huawei USG6000 Firewall Captive portal

I don't know if I'm asking this in right place. I am working on a Huawei USG6000 device to make a hotspot solution (External Captive portal), this is the schema of my working: WAN IP :10.10.0.7 ...
0
votes
1answer
1k views

Does Cisco-IPSLA work with Huawei-NQA?

I want to monitor udp-jitter using IP SLA (Cisco Router). The Destination Router was Huawei Router. I'm not sure whether Huawei Router doesn't support IP SLA responder. Is there anyway to use NQA with ...
0
votes
0answers
10k views

Huawei Router Telnet and SSH configuration - Authentication

I am following Huawei user guide to enable telnet server and telnet service to a port. However, whenever I am trying to do a telnet, I see this error and the connection times out - HUAWEI %%01SOCKET/...