Questions tagged [juniper-junos]

A tag for questions involving Juniper Networks Operating System (Junos) software.

Filter by
Sorted by
Tagged with
1
vote
1answer
35 views

Juniper vMX Routers can't ping each other in GNS3

I have a couple of VMX Routers setup in GNS3 that are directly connected on their interface, ge-0/0/2 and they can't ping each other. PFB configuration. I can't seem to find the problem! UPDATE: Added ...
1
vote
3answers
3k views

Juniper EX how to clear route forwarding table?

After layer 3 routing a large IPv6 assignment on an EX Juniper switch, the route forwarding table filled up and some entries corrupted or became otherwise invalid. We want to clear the whole table. ...
0
votes
1answer
377 views

JunOS: FPC Major error alarm

I hope everyone is doing fine! This morning I've run into a problem. My uplink interface went down for unknown reasons. Upon checking system alarms I see this: show system alarms 1 alarms currently ...
2
votes
1answer
33 views

Junos not automatically advertising an address configured on loopback interface to OSPF

According to JNCIP study guide(page 156) from 2003, the Junos should advertise a prefix on lo0.0 interface to OSPF if the RID is not manually configured: JUNOS software automatically advertises a ...
0
votes
1answer
53 views

Junos: how to change BGP MED for secondary node?

I have vSRX cluster, which announce some protected addresses over IBGP. Each node has two sessions with two routers. (I use ge-0/0/1 and ge-7/0/1 for that). I found that if fail-over happens, and ...
0
votes
1answer
44 views

What's the point of aggregate routes when the default preference is reject?

studying for my JNCIS-SP and finally digging into the minutiae. I'm trying to grasp the default behavior of aggregate/summary routes. Why are these a reject? Maybe I'm just using them wrong, but here'...
0
votes
1answer
84 views

Can't log in after admin password change

I reset my admin password with below command: #Set system login user admin authentication encrypted-password <new password> But now i can't login to my device, what can be the reason?
4
votes
1answer
589 views

Partially Faulty QSFP+ breakout port - possible config error?

Network Equipment: Juniper Ex4600, 40GbE QSFP+ -> 4x 10GbE SFP+ DAC cable, Mellanox ConnectX-2 Problem: One of the SFP+ physical link cannot be brought up (xe-0/0/25:0 Physical Link Down, xe-0/0/25:1,...
0
votes
1answer
22 views

PEM Modules Redundancy in Juniper SRX3600 series Firewall

We have Juniper SRX3600 running in our network. At the moment only 2 x PEM Modules (AC Power Supply) are installed in the chassis while other 2 x PEM are not. This is shown below from the output of '...
0
votes
2answers
40 views

juniper router /var directory is full , deleting .tgz file in root directory

i need to free some space on my juniper router , in the root directory when i use >ls -lash command i see a .tgz file which is 405 M , my question , if i delete this will it cause any problem ?
2
votes
1answer
110 views

Juniper SRX sniffing

I've a Juniper SRX 340 Cluster (15.1X49-D70.3) on which I have to do some debug. I know how to sample packets on interfaces and my question is: is it possible to sample traffic at the same time on ...
0
votes
1answer
94 views

JunOS: How to copy the config file to TFTP server?

Model: j6350 JUNOS Software Release [12.1X46-D65.4] Is there an easy way to copy the config file to TFTP?
4
votes
1answer
617 views

IPv6 default route not being installed from RA

Platform: Juniper SRX300 Version: JUNOS 15.1X49-D160.2 ISP: Midco I currently have an issue where the IPv6 default route is not being installed from the CMTS RA. Try as I might, I cannot get ...
1
vote
1answer
1k views

what do em0, em1, em2 and em3 interfaces refer to on Juniper routers

Can someone explain what these interfaces are for? I know em0 is used as a management interface on the router to connect via ssh but why are the other two there? I have also noticed, sometimes they ...
0
votes
0answers
23 views

router not learning the default route announced by RIPv2 if the same route exists via a better path

Let's say, that one has a following simple network topology: r1 ◄ ► r3 ▲ ▲ ▼ ▼ r2 ◄ ► r4 All four routers speak RIPv2 on all interfaces. r1 and r2 announce the default route which means ...
0
votes
0answers
33 views

NTP Sync issues between Palo Alto 3260 and Juniper MX10003

I'm using a Microsemi S650 as the primary ntp server and a Juniper MX10003 as the secondary ntp server. I have the palo alto 3260 configured as follows: [edit deviceconfig system ntp-servers] ...
2
votes
2answers
52 views

How to view a privilege level attached to a command in Junos?

According to Juniper documentation, each top-level CLI command and each configuration statement has an access privilege level associated with it. Is there a command which allows one to see the ...
2
votes
1answer
70 views

Juniper SRX Application Inactivity Timeout

Will the inactivity timeout set for the application "TCP-ALL" of 900 trump the default value of 1800 for junos-ssh if the application-set were matched in a security policy? Does it matter if the order ...
1
vote
1answer
36 views

Juniper vMX logical system

Can some one please tell that Juniper vMX supports how many logical system? Some one mentioned on Juniper forum that it supports 15 Logical systems but in case of 3 Logical systems configured , 2 were ...
1
vote
2answers
395 views

How to choose the most recommended Junos release for MX router

How to choose the most recommended Junos release for MX router? I need to choose a Junos OS release to update my Juniper MX960 routers from release 18.1R3, but I cannot find a procedure or best ...
0
votes
1answer
69 views

Managing a Juniper EX4300 In Band

Currently, our ex4300 are managed in band using irb.20. show configuration interfaces irb unit 20 { family inet6 { address 2001:db8:1::252/64; show configuration routing-options rib inet6.0 {...
2
votes
1answer
42 views

If accept IP address term before discard port term, will the IP's port still be discard?

In my Juniper Router MX480's firewall filter DENY-EMAIL-PORT: dele@MX-RE0# show firewall filter DENY-EMAIL-PORT term ALLOW-IP { from { address { 102.100.100.1/32; ...
2
votes
0answers
35 views

CA certificate and Local certificate

There is something which is bothering me when i think about the CA cert and Local cert. Below are my queries which pertains to juniper but may be generic as well. 1) "request security pki ca-...
1
vote
1answer
64 views

Will the router crash when it is sent routes that it can't design to hold?

I am working with a Juniper router which has the capacity to hold 60M routes in the RIB and 4M routes in the FIB. Should the router crash when more than 4M routes are being sent to FIB, considering no ...
4
votes
2answers
2k views

Can you only allow local login when TACACS is unavailable on a Juniper?

I'm pretty sure you can do this in the Cisco world, but haven't found a way to do this on a Juniper device. Is there a way to restrict local accounts from being accessed if the router has access to ...
2
votes
1answer
1k views

ERROR: Package signature validation failed. Aborting install. When upgrade the JUNOS

My device is EX4300. I use the bellow command for upgrade the JUNOS version by: request system software add reboot /var/tmp/jinstall-ex-4300-14.1X53-D47.3-demostic-signed.tgz I get the bellow error:...
4
votes
1answer
161 views

mp_reach_nlri bgp Update with 4-byte Community ASN?

I am BGP peering with a Juniper OS router. When starting the connection, my system advertises 4-byte ASN capability, which is accepted by the Juniper router: Jul 28 00:33:00.664202 BGP RECV 4 Byte ...
0
votes
2answers
45 views

Why doesn't kernel itself had entire L2/L3 protocol stack? [closed]

I know kernel itself handles protocols in layer 2, layer3 and layer 4 at ipv4 stack, but why can't kernel itself doesn't have protocols such as STP/RSTP/xSTP/OSPF...etc, implemented. Why should we ...
3
votes
1answer
1k views

next-table may loop

Help me to understand such situation. It is necessary translate a little of config from Screenos to Junos. Screenos issue: set vrouter "trust-vr" set route 217.118.52.149/32 vrouter "TrustGi-vr" ...
4
votes
1answer
64 views

set cli complete-on-space Cisco equivalent

Does anyone know what would be the equivalent, if any, of the Juniper command set cli complete-on-space for Cisco? I used to work with Juniper devices and I LOVED this feature, but now we are ...
0
votes
2answers
215 views

Deny ssh access from CPEs in all routing-instance - Juniper MX960

I try to deny ssh access from routing-instance CPEs in Juniper MX960 device. I want to know if there is a way to deny only ssh access attempt from any routing-instance.
1
vote
1answer
63 views

ex4200 bootup warning

we have some old juniper ex4200 in our stock and it shows following warning in console : --- JUNOS 12.3R3.4 built 2013-06-14 00:08:02 UTC *************************************************************...
0
votes
1answer
92 views

Junos, accidentally deleted a FIB entry, how to re-add?

while i was testing Junos in a virtual environment, i accidentally deleted an entry in the forwarding base (do not clearly remember which command i used to let that happen), but because of this the ...
1
vote
1answer
39 views

Where the `term` and `policer` would appear?

Where the term and policer would appear? In juniper, there have filter, term and policer. I know the filter is under firewall, but how about the term and policer? how to understand the concept? I ...
1
vote
1answer
348 views

Junos OS Upgrade on EX4200 Virtual Chassis

We have couple of EX4200s switches in Virtual Chassis mode running in the network. Each Virtual chassis has only 2 member switches. We are required to upgrade the Junos OS on each member switch in ...
3
votes
1answer
152 views

How to bypass when network speed over a special number in Juniper?

I have a requirement, such as I have 113.100.15.0/24 segment IP addresses. in Juniper M480 Router I connected to BGP-A(1G) and BGP-B(10G), by default the 113.100.15.0/24 out the Router it go ...
0
votes
1answer
229 views

What is the point of Junos outbound SSH service?

Junos outbound SSH service makes a SSH connection from network device to SSH server. What is the point of this? Does it allow the server to somehow make the SSH connection back to network device using ...
2
votes
1answer
124 views

Wildcard to match JUNOS

Hi I am trying to match routing instances with names other then VPLS-* basically any name that starts with V* but is not VPLS-* I tried multiple different iterations of below but it seems to ignore ...
3
votes
2answers
546 views

What's `irb` meaning? and what's the difference between it and `vlan`?

What's irb meaning? and what's the difference between vlan? I found some Junos version the vlan l3-interfaces should be vlan.xxx, and some times there is irb.xxx. irb { unit 0 { family ...
1
vote
0answers
2k views

TACACS with Juniper Devices

Can any one please help in configuring a TACACS+ server, along with configuration in Juniper devices? Ubuntu Server 14.04 Juniper QFX5100 switch Below are my configurations: For the TACACS+ server: ...
0
votes
1answer
31 views

Filtering http/https traffic destined for a juniper router

I need to find a way to harden my network so that all juniper routers reject web management and any http / https traffic that is destined for them specifically. This is what I came up with so far: ...
4
votes
3answers
448 views

JunOS, access mode interface asks for a vlan

I'm kinda new to networking so I'm going to do my best to try explain my issue. The issue that I have is that I want to delete all default configuration for my xe interface. Current configuration: ...
1
vote
1answer
165 views

How to do port mirroring in Juniper EX2200 switch

I am using Juniper EX2200 switch, one of the connected System generating lot of unwanted traffic ( varying from 10 Mb to 25 Mb upload traffic). I wanted to analyse those traffic using port mirroring ...
1
vote
1answer
290 views

EX3300 can not use irb.x, so how to access the layer-3 address?

EX3300 can not use irb.x, I have a Juniper EX4300 convergence layer Switch, in it there are irb interfaces. such as irb.3, and if I have another EX4300 for access layer, I can set vlan l3-interface ...
3
votes
1answer
43 views

Every `aex` have a `aex.0` in my QFX5100, why?

When i show interface terse in my Juniper switch qfx5100: .... ae29 up up ae29.0 up up inet 192.168.9.2/24 ae30 up up ae30.0 ...
0
votes
1answer
978 views

The irb interface can not ping in EX4300 itself

In my Juniper EX4300 I created a irb.2 with address 10.10.10.110/24 irb { unit 2 { family inet { address 10.10.11.110/24; // the snapshot is wrong, I changed to 10.10.11.110/...
1
vote
0answers
238 views

What's the uplink port shows in the `show interfaces terse`? [closed]

My Juniper EX4300 have four uplink port: but when I show interface, there only two xe port: Interface Admin Link gr-0/0/0 up up pfe-0/0/0 up up pfe-0/0/0.16383 up up ...
3
votes
1answer
375 views

Juniper Radius Configuration

I'm trying to figure out how to setup radius on a Juniper EX2300. The juniper can reach the server no problem, but when I run the 'test aaa authd-lite user [user] password [password]' command, I get ...
6
votes
2answers
1k views

Can Junos show a matching config statement in context, like IOS `| section`?

Hard to describe what I'm asking. For example, here's a section of my config, with the full hierarchy: interfaces { ge-0/1/9 { vlan-tagging; unit 100 { description "my ...
3
votes
1answer
173 views

Site-2-Site Juniper SRX & Zywall

I've a Juniper SRX 340 on my datacenter and a Zywall USG 100 on my office. I'd like to build a site-to-site VPN between them, but after a lot of tries I can't still reach the result. This is the ...

1
2 3 4 5 6