Stack Exchange Network

Stack Exchange network consists of 175 Q&A communities including Stack Overflow, the largest, most trusted online community for developers to learn, share their knowledge, and build their careers.

Visit Stack Exchange

Questions tagged [qos]

For questions about Quality Of Service (QoS); all aspects of providing differential service to packets based on TOS, DSCP, or other information.

0
votes
1answer
35 views

Cisco nexus 9396PX TX output discard on 40G interface without link congestion

We have cisco nexus 9396PX with N9K-M12PQ module (12x40G Interface), We have 8x10G L3 LACP bonded connectivity with our ISP and so far so good no issue at all. but recently we migrated that LACP LAg ...
0
votes
0answers
11 views

Ftp uploads are slow on windows, not macos or Linux [on hold]

Our church only has dsl avaliable to the area, so we currently have 8 runs of 25up 5down dsl from telus bonded by skyway west. It works decently all except for one thing our ftp uploads are very slow ...
2
votes
1answer
55 views

Do unmanaged switches honour QoS priorities set by managed switches?

Details about the devices We have a 24 port NETGEAR managed POE switch that has QoS capabilities. We also have the following unmanaged switches, 24 port Cisco POE, 48 port Cisco, 48 port NETGEAR, ...
1
vote
0answers
18 views

Can QoS provide a benefit after data has gone through other unmanaged switches first? [duplicate]

Details about the devices We have a 24 port NETGEAR managed POE switch that has QoS capabilities. We have the following unmanaged switches, 24 port Cisco POE, 48 port Cisco, 48 port NETGEAR, and 24 ...
3
votes
2answers
62 views

Trust dscp command missing on cisco 3850

We have an incoming QoS configuration on our 2960X switches like this: class-map match-any QOS_GL_TRUST match ip dscp 8 16 24 32 46 class-map match-any QOS_GL_CITRIX match access-group name ...
2
votes
1answer
83 views

Cisco Unity Connection guest, ESXi host, IP phones, vlan, subnet, ip addresses, qos

I have setup: VLAN 1 and subnet 192.168.1.0/24 for data VLAN 100 and subnet 192.168.100.0/24 for voice IP phones get their IP via DHCP on the subnet 192.168.100.0/24 all other IP devices get their IP ...
1
vote
1answer
38 views

QoS - Add DSCP EF tag with L2 switches?

Here is the topology that I have: Phone => (access port) L2 Switch (trunk) => Router My goal here is to add an EF tag to the packets coming from my phones. Basically, if a packet comes in being in ...
0
votes
0answers
14 views

Why in DRR (Deficit Round Robin) is the Deficit Counter set to 0 when the list of packets for a flow gets empty?

I'm studying DRR scheduling algorithm (https://www2.cs.duke.edu/courses/cps214/spring09/papers/drr.pdf) but I don't understand why the deficit counter is always reset to 0 when the list of a flow get ...
22
votes
10answers
23k views

How to generate traffic for lab scenarios [closed]

I'd like to start exploring QoS, and lower level optimizations for things like broadcasts/multicasts within my home lab. I've looked around for ways to generate traffic to and from a box, but haven't ...
1
vote
1answer
48 views

C3PL working order

It is very hard to find information on this topic. I would like to know: If traffic has a hit inside a class-map, is it immediately forwarded or does it get checked against all remaining match ...
1
vote
1answer
35 views

Fair-queueing every class within CBWFQ

My question is similar to: What is benefit of using CBWFQ with fair-queue statement Given this policy-map (without class-maps) configuration: policy-map test class DSCP30 bandwidth percent 20 ...
0
votes
1answer
33 views

qos inside vpn, possible or not ? I read yes and no

I am wondering if possible to do QOS (or similar action) inside vpn tunnel to a cloud server. the goal is to reserved bandwith for voip traffic. I read that you can with GRE and other people said, ...
2
votes
1answer
53 views

Cisco QoS SRR Share & Shape impact

I am working on understanding the impact of using shaping and sharing with the SRR scheduler. Given these 2 commands on an interface: switch(config-if)#srr-queue bandwidth share 40 20 30 20 switch(...
3
votes
2answers
97 views

Hierarchical QoS

As I understood, the main difference between H-QoS and QoS is the level of category granularity, in which we could apply different QoS tools and policies. For example in simple QoS, just ...
3
votes
1answer
55 views

QoS on 2960X does not seem to have an impact

We have some issues with Dect stations that have a very high requirement in regards of delay. Communication between 2 devices should not exceed 500 microseconds (0.5ms). We decided to test some ...
1
vote
1answer
24 views

QoS Classification and Drop Rate

Sorry if i sound completely senseless, In CBWFQ, q1) Does WRED only make sense if there is more than 1 dscp marking in a queue ? q2) if traffic_typeA is to be handle with higher priority then ...
0
votes
1answer
34 views

CISCO Tc Bc and CIR units

Are the units in these formulas correct? Tc (seconds) = Bc (bits) / CIR (bits per second) Tc (milliseconds) = Tc (seconds) * 1000 Bc (bits) = Tc (seconds) * CIR (bits per second) CIR (bits per second)...
3
votes
1answer
27 views

Access and uplinks ports QoS Queuing model

On an access switch, does the uplinks egress QoS Queuing model (multiple traffic classes and bandwidth reservation), should be different than the access ports egress Queuing model ? Is there a sense ...
1
vote
2answers
28 views

what is the difference between OpenFlow queue and 802.1p

I was reading about queues and I came across OpenFlow Queues and IEEE 802.1p I would like to know what are the main differences between them, and how they treat the traffic. In other words how they ...
2
votes
1answer
29 views

Is WRED configured for TCP traffic only?

I am looking out for a practical usage of WRED. After reading/searching I found that it is more suitable for TCP traffic. When the queue is full, all the TCP session at that time will start with slow ...
5
votes
1answer
67 views

Cisco ISR - Police & burst

We have a Cisco C2900 ISR here, with the following configured: policy-map XX_4M _IN police rate 4000000 burst 400000 conform-action transmit exceed-action drop The policy-map is applied on an ...
1
vote
2answers
132 views

How to block youtube url on a cisco router

How can i block youtube on a cisco router? I have already used class map as seen below class-map match-any url-block-class match protocol http host "*youtube*" ! policy-map block-class policy-map ...
0
votes
0answers
24 views

What is the difference between Custom Queuing and Weighted Fair Queuing?

I understand that both mechanisms send traffic in a round-robin fashion, and the traffic is sent proportionally to their weight based on the ToS of the traffic. However, I don't understand the ...
2
votes
1answer
72 views

Cisco QoS trust and cos-dscp dscp-cos Mapping behaviors

Regarding our current Cisco QoS implementation, to get a deeper understanding I would have some questions I read this: https://www.cisco.com/c/en/us/support/docs/wireless-mobility/voice-over-wireless-...
0
votes
1answer
41 views

How color is encoded in the DS field/ToS IPv4 - QoS?

The RFC 2698 says - "The color is coded in the DS field [RFC2474] of the packet in a PHB specific manner". I am trying to understand how color is encoded like in the IPv4 header - in the TOS field ...
0
votes
1answer
37 views

QoS color aware and color blindness?

QoS - Color Aware and Color Blind mode. Is color - red, yellow and green is a kind of analogy for violate, exceed and conform traffic rate. If so, whey did they come for the colors here. I mean ...
9
votes
2answers
2k views

QoS woes - managed IP VPN

(First of all, I'm sorry for this wall of text. I don't know how to make it any shorter without losing important information. I originally wanted to use the chat room for this, like we do on ...
2
votes
2answers
175 views

QoS for OSPF, VOICE and CRITICAL Traffic

I plan to implement the QoS policy below. The target is to garantee bandwidth to VOICE and CRITICAL traffic. It should be 1/3 for Voice and Video, 1/3 for Business Critical traffic, 1/3 for all the ...
0
votes
2answers
43 views

traffic shaping

I need some clarifying on that issue (little bit rusty on that) Assuming I have some limitation on the BW of 1Mb. What will happen then there is incoming traffic of 1.5Mb for 10 sec - some of the ...
3
votes
2answers
124 views

QoS: priority-queue out

I'm trying to understand the priority-queue out command configured on an interface. Based on what I have read, here is what it does : the Priority Queue (Queue 1) on the switch will be emptied before ...
0
votes
0answers
86 views

Cisco QoS Queuing models

I would have a question about the Cisco Queuing models. For example, when we speak about 1p7q3t, or 2p6q3t, or others models, does it from hardware or software considerations ? If it's hardware, if ...
1
vote
1answer
36 views

I limit the port INGRESS but get packet loss

I use the limit speed method to limit the Juniper Switch port EGRESS and INGRESS speed. but after I added the INGRESS filter to my port, there will loss packets on the switch every port. anybody ...
5
votes
1answer
363 views

Traffic marking is not working properly in QoS

Traffic marking is not working properly in QoS. I have a problem with the policy map marking bit. I would like to monitor the traffic that matches the IP precedence bit 4 in Po 50, but from the ...
1
vote
2answers
515 views

Confirm QoS Cisco 3650

I'm testing some Cisco 3650 switches with Cisco VoIP handsets and using auto qos. Is there a way to see if qos is kicking in and prioritising the voice traffic? Tried looking through the cli and can't ...
3
votes
1answer
203 views

Throttle traffic over a link?

I work for a global company in the client support department. Another department manages the network. My team is frequently asked to throttle client traffic from our on-premises Apple software update ...
2
votes
1answer
265 views

QOS police vs bandwidth - is this configuration wrong?

I understand bandwidth in QOS is use to guarantee a minimum bandwidth I understand police in QOS is to set a limit to the maximum bandwidth. class test_out police **1608000** 50000 100000 conform-...
1
vote
2answers
493 views

How do I prevent any one user from hogging all the bandwidth?

We upgraded from 20 Mbps to 50 Mbps DIA about two months ago. This required a router upgrade as well. Since then, anyone who starts a large HTTP download - e.g. an ISO, large spreadsheet or log, movie ...
1
vote
1answer
392 views

How packets get differentiated to prioritize?

On the Internet, there are many types of packets: VoIP, Audio, Video. As QoS is used to prioritize packets based on DSCP or VLAN priority. who set these bits for each and every packet. Like Audio gets ...
2
votes
1answer
177 views

Rate limit based on VLAN

My ISP company has some PoPs in remote areas, as shown in diagram. It is currently, it's getting all prefixes from Local IX and getting only a default route from the upstream Internet provider. ...
1
vote
1answer
302 views

Cisco IOS: Limiting internet bandwidth usage for specific VLAN

I would like to limit the usage of a 10 MBit internet connection for a specific internal VLAN to 2 MByte (on a Cisco router, IOS 15.3). Is that possible in general? How can the router make sure that ...
0
votes
1answer
90 views

DSCP re-marking on Cisco Switch

I've followed the commands in this post: DSCP trust boundary policy-map MARKDOWN class class-default set dscp ef Interface Config: interface gig 0/1 service-policy input MARKDOWN The ...
3
votes
1answer
64 views

Is Cisco SG300-10PP & QoS appropriate to share bandwidth?

We're going to let some empty space in our office building soon. The potential client needs an internet connection for their systems (including VoIP).For ourselves we have a resilient ethernet setup, ...
10
votes
1answer
1k views

Does IP provide QoS or not?

IP provides a best-effort delivery service. I believe this implies, among other things, that it offers no QoS to the users. However, IP has a byte in its headers (ToS in v4 and Trafic Class in v6) ...
0
votes
1answer
51 views

Latency in Network [closed]

My company uses trading application where latency is utmost important. I have few ideas but really dont know how to implement. Like I want to know 1) How can I Prioritize applications by 802.1q tag. ...
1
vote
1answer
430 views

Cisco 3850 Output Drops IOS XE Everest Version 16.6.1

We have a MPLS link connected to our 3850 with voice traffic, our interface have 1Gbps and the link is limited to 200Mbps. Our interface shows output drops, and the client device shows overruns. What ...
2
votes
1answer
549 views

Quality of Service: Questions about input and output service policies prioritizing the same traffic

This question/lab was created with Cisco networking hardware. I have asked this question else where with no responses. I am new to QoS, but I have spent the last few days researching and I've ...
2
votes
1answer
55 views

HP 6120X Blade switch QoS

I just got access of blade center and i was looking at configuration of switch which is following. I can see switch has already QoS configured, I am not very expert in QoS so trying to understand ...
3
votes
1answer
1k views

Default QoS Behavior on Catalyst 3650/3850 Running IOS XE 16.3.6

I am trying to better understand the default queuing behavior on Catalyst 3650/3860 running IOS XE 16.3.6 Denali. Is QoS enabled globally by default? Coming from working with Catalyst 2960X on IOS 15 ...
1
vote
0answers
43 views

traffic of AF41 marking under interface

I have used port-queue commands most of the time to check traffic status under BE, EF, AF4. But I haven't found command to check for AF41 to AF42 on Huawei VRP or cisco IOS. How can check traffic of ...
2
votes
0answers
53 views

Service Policy CISCO 7606 not work [closed]

I have bandwidth control in cisco 7606 but the same is not limiting my clients. I checked the settings and did not identify an error. This box is 1 replacement for 1 old 7606 model. Is it necessary to ...