Questions tagged [qos]

For questions about Quality Of Service (QoS); all aspects of providing differential service to packets based on TOS, DSCP, or other information.

Filter by
Sorted by
Tagged with
0
votes
1answer
17 views

How to compare two DSCP ? which one of DSCP 28 and 34 (decimal) has more priority?

How to compare two DSCP ? for example which one of DSCP 28 and 34 (decimal) has more priority ?
0
votes
1answer
17 views

Traffic flow of tunnel interfaces

I would like to understand traffic flow in a router. In what direction do i need to apply a policy-map in order to affect traffic? Especially regading tunnel interfaces, as traffic both comes and goes ...
0
votes
1answer
123 views

How color is encoded in the DS field/ToS IPv4 - QoS?

The RFC 2698 says - "The color is coded in the DS field [RFC2474] of the packet in a PHB specific manner". I am trying to understand how color is encoded like in the IPv4 header - in the TOS field ...
0
votes
1answer
59 views

What kind of QoS do I need? [closed]

I have a small office. There are ~5 PCs connected via cable. There is 1 PC via WiFi, 3 VoIP phones and a bunch of cellphones connected via WiFi. There is a Gigalan switch and a internet connection ...
0
votes
1answer
941 views

Bandwidth regulation without QoS and VLAN [closed]

Does anyone know any possibility to do Bandwidth reservation or something equal to it. Mainly to give VoIP and IPTV Bandwidth before the Internet when there is no possibility to use QoS and VLAN. It ...
0
votes
2answers
89 views

What exactly happens in the queues when a congested network applies back pressure ? [closed]

During Congestion in a network switch HW ,for examplewhen a shaping rate to the interface that imposes a speed limit lower than the maximum interface line speed . The concept of back pressure is ...
0
votes
0answers
21 views

Shaper configuration for Juniper MX480 - MPC3e 3D NG

following secario: A MX480 with MPC3e 3D NG Linecards. I have a new Layer2 Access provider that is providing Layer2 services between 100 and 1000MBit/s. My connection zu this services are a 10GE E-...
0
votes
0answers
20 views

can't find cbQosCMPostPolicyBitRate64 oid for cisco

i have use snmpwalk go get police Bit Rate Traffic policy-map(QOS) for my cisco ASR1006 but i need a 64bit barbecue my traffic is more of 5000Mbps so 32bit can't handle it . ~# snmpwalk -v2c -c aaa ...
0
votes
0answers
16 views

Rate limiting xFTP traffic originating from a Cisco IOS router

We have some routers on marginal cell links that we need to pull files from using TFTP or FTP. During file transfers connections to the router become so slow as to be unusable. Is there a way to rate-...
0
votes
0answers
25 views

uncorrected snmp Qos value from cisco

hello i have a router cisco 1006 and i create a policy-map with to class policy-map CheckBand-BandPerUsr class BandPerUsr police cir 10000000000 class class-default police cir 10000000000 ...
0
votes
0answers
40 views

QoS over IPSec Site-to-Site VPN: Concerns and Questions

(For clarification purposes: Kbps = Kilobits per second for bandwidth, KB/s = Kilobytes per second for file / data transfer stuff. I'm using them separately because XG knows KBps but not Kbps - ...
0
votes
0answers
56 views

How do I set per-IP QoS on my router?

I'd like to limit per-endpoint bandwidth on my network to ~10% of available bandwidth, to avoid a single device from consuming all available bandwidth. But I'm not seeing any way to set up a bucketed ...
0
votes
0answers
23 views

What is the difference between meters and queues in Openflow?

I'm new to OpenFlow and have just started studying Software Defined Networking. I have found a multiple websites mentioning that queues and meters are complementary to each other, and that they should ...
0
votes
0answers
62 views

Applying DSCP to an interface

I'm trying to apply DSCP (AF41) to an interface eth-trunk (if it matters) - [~HUAWEI] diffserv domain QoS \ creating diffserv domain named QoS [~HUAWEI] dsdomain QoS] ip-dscp-outbound af4 ...
0
votes
0answers
78 views

I'm unable to see packet drops after configuration of QoS policy

I aim to send iperf traffic from Endpoint1(Client) to Endpoint2 (Server) with the following SR path = {R1, R2, R3, R4, R3, R2, R1, R2, and R3}. First of all, the traffic generated by iperf from ...
0
votes
0answers
59 views

Cisco Catalyst QoS queuing model

How Cisco Hardware queuing model (like 1p7q4t for Cat6800) are related to traffic classes (class-map) ? How assign the X traffic class to Y hardware queue ? Also, if only 6 classes are configured, ...
0
votes
1answer
215 views

CISCO Tc Bc and CIR units

Are the units in these formulas correct? Tc (seconds) = Bc (bits) / CIR (bits per second) Tc (milliseconds) = Tc (seconds) * 1000 Bc (bits) = Tc (seconds) * CIR (bits per second) CIR (bits per second)...
0
votes
1answer
370 views

QOS on Nortel Devices

I need to set up the following on Several Nortel Baystack's (5530/5520): "Assign a priority to DXL VoIP traffic with a DSCP priority level which will be co-exist with the rest of the real-time ...

1 2 3 4
5