Questions tagged [redistribution]

For questions about or involving route redistribution in a routing protocol. For instance, you need to find out why OSPF does not redistribute your routes.

Filter by
Sorted by
Tagged with
1
vote
0answers
100 views

Routes stopped redistributing through OSPF

I was entering a number of secondary addresses on some VLANs. In total there were 10 secondary addresses added. The subnets added were from three publically routable /24s (I will call them 25.0/24, ...
0
votes
1answer
36 views

Why does my route-map blackhole some equally specific routes? [closed]

I have a challenging situation. I have two routers, in VIRL, sharing routes via BGP and OSPF I am attempting to remove the "network 0.0.0.0 255.255.255.255 area 0" from my OSPF process. I have tried ...
1
vote
2answers
69 views

What are the biggest problem in distributed processing?

Imagine that I have someone in Bejing who offers me his supercomputer for processing an intensive job. How does it compare sending job from Berlin to Bon,to sending the same job to Beijing? I am ...
2
votes
1answer
46 views

Is the redistribution default-metric value when used over vPC peer link based on port channel aggregated bandwidth or individual physical Interface?

The question is in the title. Looking at a config where they were trying to Peering traffic over an SVI, but they have the physical interfaces bandwidth listed as the value and I am not sure if that ...
3
votes
1answer
684 views

Why OSPF E1 and E2 exist?

I know the difference between E1 and E2 metric-types. I know the preference level given to those routes. I know difference between Metric and Forwarding Metric and how it works. What I don't ...
2
votes
1answer
470 views

What is the difference between GPON ONU and ONT?

The Optical Network Unit (ONU) and the Optical Network Terminal (ONT) GEEPONs can both connect with an Optical Network Terminal (OLT) via fiber cables in order to achieve an Optical Distributed ...
1
vote
1answer
108 views

Redistribution VLSM networks to BGP neighbour with summarized 24 bit mask network

I received public BGP AS with network with 24 bit mask. Is it possible, to advertise on BGP router VLSM networks summarized to 24-bit mask (not for class membership)? Example: I receive 112.112.112....
1
vote
2answers
2k views

Why is ospf to bgp redistribution and simultaneous bgp to ospf redistribution dangerous?

I am referring to this question, where OP apparently fixed his issue by redistributing ospf in bgp and vice-versa on the same router. The user Sebastian warns that this is a dangerous practice. We ...
1
vote
0answers
194 views

OSPF NSSA - Type 7 LSA Metric Changes Unexpectedly

When a new path to an NSSA External (LSA type 7) route is brought up in the topology below, the existing path's cost to that route increments to exactly match the new path's cost. Therefore, both ...
1
vote
1answer
2k views

OSPF into BGP Redistribution issue

I am having trouble with basic OSPF redistribution into BGP. BGP peers between R10 and R12 are up. I have full connectivity between Area 0. R10 0/0 is also in that area. I cannot get BGP routes from ...
1
vote
3answers
109 views

OSPF Border Router Discovery

Hi how the routers in ospf network will discover the borders routers when i try to see the border routers with the show ip ospf border command i get : in Area 0 - R2 discover : all border ...
2
votes
2answers
84 views

In what case should the core router having iBPG configured or having routes redistributed via OSPF to it?

I have the following topology. The notebook computer has to access the internet. In what case should R3 (as the core router & default gateway for the internal network) having iBPG configured or ...
1
vote
1answer
46 views

How to configure a distributed network for the replication? [closed]

I want to replicate data (music, video, photos, user's data) across different geographical networks. How to connect several networks into a single network to let nodes comunicate to each other? ...
2
votes
2answers
1k views

Why do static routes not need a “default-metric” set when redistributing into EIGRP?

Good Afternoon, I ran into an issue this morning where static routes on a certain device weren't being redistributed into an EIGRP process configured on the same device. I'd originally thought this ...
6
votes
2answers
2k views

OSPF Route Tagging and BGP AS Prepend

Is it possible to perform the following configurations on Cisco routers, and are there any challenges with these types of configurations (mainly #3)? Match an OSPF route tag of 12000 (Definitely ...
1
vote
1answer
2k views

Redistribution between EIGRP and Static routing protocols

I have configured EIGRP and STATIC protocols between two areas and both protocols at Area border router. unfortunately I'm unable to ping between two areas, the networks are configured correctly and ...
4
votes
1answer
484 views

EIGRP to iBGP metric calculation

Consider the following output: router#show ip bgp vpnv4 rd 300:1 5.5.5.5/26 BGP routing table entry for 300:1:5.5.5.5/26, version 538213 Paths: (2 available, best #2, no table) Advertised to ...
10
votes
5answers
5k views

Static redistribution into EIGRP as internal failure

I am redistributing a static route into EIGRP on a 6500. I had read here if you enter a network statement matching a static route that it would be redistributed as an internal route by EIGRP. However, ...
8
votes
1answer
2k views

Does RIP to BGP redistribution for an MPLS VPN make sense?

A customer was recently adamant to perform redistribution of their RIPv2 routes into BGP. This is over a standard MPLS VPN solution whereby the CE routers are fully managed. This approach feels ...