Questions tagged [vyatta]
For questions about the software-based virtual router, virtual firewall and VPN products for Internet Protocol networks (IPv4 and IPv6) by Vyatta. All network products made by Vyatta.
12
questions
0
votes
1
answer
44
views
VPN Traffic Routing on Ubiquiti/Vyatta
I'm using Ubiquiti to route certain outgoing ip-ranges through a VPN. I would however like to route all HTTP/HTTPS traffic via the VPN except large downloads.
I realize that this is a tall order, but ...
- 101
3
votes
3
answers
2k
views
Monitor Vyatta router VPN through SNMP
I would like to monitor/manage VPN /Tunnel for Vyatta router 5600 through SNMP . Can't find mib or specific OID for the Vyatta router 5600. ?
Please answer with Mib or SNMP OID .
Thanks in advance
2
votes
3
answers
2k
views
How to make IPSec VPN tunnel to work from behind NAT on ADSL?
I want to establish a VPN tunnel with AWS using IPSec (Vyatta).
There is something that I was not able to figure out: How do I make it work without having to configure a static IP for the customer ...
- 121
2
votes
2
answers
1k
views
vyos, wan load balancing with one static and one pppoe connection
I have two ISPs, one static and one PPPoE. I use VyOS.
I did the configuration with two static IP providers but when it comes to PPPoE I don't know what to write as the next hop for the interface ...
- 33
2
votes
2
answers
2k
views
VyOS / Cisco ASA 5520 site-to-site VPN traffic drops after ~10 minutes
I am trying to setup a site-to-site VPN to a large telco.
We are running VyOS 1.1.7 in AWS; they are using a Cisco ASA 5520.
Since the telco is large, and we are small, they have dictated all the ...
- 131
3
votes
2
answers
2k
views
Alias IP Address in VyOS
I have a network where I am looking to alias an IP address/port and redirect it to another machine.
VyOS is on my network at 192.168.55.1 and I have another device on the network at 192.168.55.66. I ...
1
vote
1
answer
648
views
Mail server behind Vyatta NAT with two WAN connections
I have a Vyatta router with eth0 and eth1 on the same network segment ex. 99.99.99.0/24 where eth0 is .1 and eth1 is .2 and this is the wan network segment.
The traffic to the default gateway is ...
- 33
1
vote
0
answers
207
views
BFD support for OSPF vyatta 6.2?
Is it possible to get support for BFD for OSPF on vyatta 6.2?
I cannot find any information about it on the internet. The only thing I've seen is that the support is available on Brocade Vyatta 5400 ...
- 183
3
votes
2
answers
1k
views
OSPF can't ping other network segments
I'm trying to setup a very simple OSPF network with Vyatta. From the best of my knowledge they let all traffic in by default, and I haven't set any firewall rules. The vyatta instances are launched as ...
- 183
2
votes
2
answers
642
views
Vyatta/EdgeOS remote access VPN without NAT?
I currently have a ubiquiti edgerouter setup with an ipsec site-to-site vpn and l2tp/ipsec remote access vpn. Both work as intended.
Is it possible to configure the remote access (l2tp/ipsec) vpn to ...
- 391
1
vote
1
answer
9k
views
I disabled an interface in vyatta, how do I enable it?
I entered set interfaces eth0 disabled which worked. show interfaces shows that the interface is administratively down. However I can figure out how to bring it back up.
- 13
2
votes
2
answers
2k
views
OSPF route filtering on Vyatta device
We have a connection between our Vyatta Router to our MPLS VPN Service Provider which is a Cisco device.
We would like to know how to filter the OSPF advertisement routes on Brocade Vrouter 5400 (...
- 2,008