Questions tagged [vyos]
For questions about the software routing platform VyOS for Linux and Unix. Only use this tag in relation to on-topic network devices and only if your server is a dedicated network device.
15
questions
0
votes
1
answer
17
views
Which technologies are most relevant for mobile broadband ISP bonding? [closed]
If I have edge router and core router (kind of Hub) and few ISP lines between them what are the most relevant technologies to be used for mobile broadband bonding?
Expected result is:
if one of ISP ...
- 101
2
votes
1
answer
130
views
Static route removes another static route
In the following diagram each Vyos router has RIP configure and R1 has NAT to allow hosts from 10.0.0.0/24 and 192.168.10.0/24 accessing the internet. The goal is to put the PCs comunicating with each ...
user80646
3
votes
2
answers
3k
views
Configure NAT in Vyos Router
I have the following diagram, and I want that R2 and each client connected with R2 have access to the internet. For that I configured NAT in R1 with the following commands:
#set nat source rule 10 ...
user80646
0
votes
1
answer
2k
views
Simple VyOs Static Routing on GNS3
Sorry for the beginner question. I'm trying to simply set up static routing on this GNS3 topology. Specifically, I want Sam to be able to ping Jack. I've assigned all of the VPCS machines ip's, and ...
- 1
2
votes
1
answer
229
views
VyOS: Failure to commit after L2TPv3 configuration
I am trying to get familiar with VyOS (using a VM) and while working on L2TPv3 I encountered something strange: after configuring the L2TPv3 interface and try to commit, an error occurs as if the ...
- 147
3
votes
1
answer
1k
views
Monitor VyOS Router
I'm actually using VyOS 1.1.8 an i wan't to collect the eth0 interface traffic to send it to a centralized syslog server. The thing is that i want to have the net traffic in some format like squid ...
2
votes
0
answers
131
views
VyOS Boot configuration
When I instantiate VYoS VNF on openstack, I could see IP address allocated to instance but it is not setting any address on the instance interface. I had to manually update interface address from ...
- 21
4
votes
1
answer
6k
views
Vyos Default route
I have set a default route on vyos using the command:
set protocols static route 0.0.0.0/0 next-hop 10.121.191.254 distance '1'
But, the route appears to be inactive. The interface through which it ...
- 163
1
vote
0
answers
244
views
Monitoring interfaces on VyOS then SSH output to another machine (Security Onion) [closed]
I am trying to figure out the best way I can monitor interfaces on a VyOS interface from a Security Onion instance using Squil (Snort alerts etc). I am thinking SSH to VyOS to activate monitor ...
- 11
2
votes
2
answers
1k
views
vyos, wan load balancing with one static and one pppoe connection
I have two ISPs, one static and one PPPoE. I use VyOS.
I did the configuration with two static IP providers but when it comes to PPPoE I don't know what to write as the next hop for the interface ...
- 33
2
votes
2
answers
2k
views
VyOS / Cisco ASA 5520 site-to-site VPN traffic drops after ~10 minutes
I am trying to setup a site-to-site VPN to a large telco.
We are running VyOS 1.1.7 in AWS; they are using a Cisco ASA 5520.
Since the telco is large, and we are small, they have dictated all the ...
- 131
3
votes
2
answers
2k
views
Alias IP Address in VyOS
I have a network where I am looking to alias an IP address/port and redirect it to another machine.
VyOS is on my network at 192.168.55.1 and I have another device on the network at 192.168.55.66. I ...
1
vote
0
answers
989
views
Connection problem, site-to-site, VYOS
I'm having problem with a site-to-site. I think I have the basic setup working and I want to confirm that the tunnel is up and working. Here is what I have:
vyos@<vpnxy>:~$ show vpn ipsec sa
...
- 131
2
votes
3
answers
592
views
Should I ask for fewer routes or use a route-map to reduce table-size?
I'm running a Vyatta based BGP-router with multiple transit providers which send full BGP tables. I'd like to reduce the load generated by route-calculation but want to keep some possibility of ...
- 21
4
votes
1
answer
2k
views
Matching a community in a route-map
I am trying to set the local preference of certain routes based on the community string. I created the community list and confirmed it is working by checking the routes reported matching the ...
- 143